Відео

Has lathe but no press?

mas aquilo n é um torno? kakakak

amigão como faço para comprar um cano calibre 38

You should invest in a small like er32 collet set to use as your milling attachment. Jacobs chucks are not good for milling. I'm impressed it works so well for you though. Lots of good knowledge here

We're intelligent but too poor to aquare the tools and materials for different inovatio

If u must use a secondary chuck then mount it on a shaft and backing plate then grip this shaft with primary chuck . THE REASON is a secondary chuck is gripped only by small jaw contact from primary chuck and the work held in second chuck becomes a lever as the tool is fed into work therefore weKening the grip of primary chuck on secondary chuck .The first u will know Bout it is when the secondary chuck and work is flyiing thru the air like a missile .You have been warned of potentially very dangerous situation . MOUNT THE SECOND CHUCK ON A RIGID ADAPTER SYSTEM THEN GRIP THAT WITH THE FIRST CHUCK .my reaon is simple .The first chuck has a shaft to grip on and if it loosens it has to walk out of first chuck a long way to be dislodged .depending on the length of mounting shaft this is your safety margin if the second chuck begins to walk out of first chuck .

When u piggy back a chuck the sdcond chuck can be diodged by many things including chattering tools or a tool digs into work causing thd second chuck to be a heavy missile thrown out of lathe . .BEWARE OF THIS RISK .

First of all, you should take a Torch and heat down all up when you pound it through. And it would have been nice to have some measurements for what you did.

Creative video, thank you :)

S45C is equivalent to EN8. On a manual lathe you'll get a better finish using HSS tools and taking deep cut, rather than using what looks like braised carbide

Que bosta

Cool work thanks 👍

Ты молодец , конечно - нам так не жить . Пока месть ... .

Lunette Diabolo.........................................................connue depuis des siècles!!!!!!.........

"step 3, use a lathe"

Bisa pesan bos

torna nedir. sen bilmiyorsun sanırım. bağladığın makinanın adı torna ve onda yapılabilir ancak yasal değil...

Si c'était si simple et pas interdit en France 😂

bro is making a 50 cal derringer

saya mh pengen as derat seperti pembuatan alat honing.tapi derat dan mur nya.kira-2 berapa ya?

just I´need some that this, thank you and congratulations

Do you think people who are having workshop 100 yrs /50years old Are idiots better change the topic of the videos Maker and editor are big idoits chutiye bhare hue hai aise channel pe

👍👍👍👍👍👍👍👍👍👍👍👍👍

Cool

Потому,что такому дебилизму не учат в учебных заведениях!

Конечно не многие , в каменном веке же блять живём . Куда нам с палкой и камнем 😂😂😂😂

Ой зря палец в шатун засунул на вращающемся патроне! Нарушение техники безопасности! А вдруг задир, стружка из смазочного отверстия случайная, оторвёт ведь!! Oh, I shouldn't have stuck my finger in the connecting rod on a rotating cartridge! Violation of safety regulations! And suddenly the bully, the shavings from the lubrication hole are accidental, they will tear off after all!!

А где выстрел?импульса ударника без применения порохового заряда вообще не хватит для какой нибудь порожающей силы.я готов поспорить что кусок свинца автор просто прогнал через ствол для имитации прохождения по нарезам,а потом аыстрелил этой хернёй из рогатки по бутылке.не все такие тупые чтоб этого не понять

vidionya terimakasih

no its no good

Yeah great how to make wepone's great not

คุณอยู่ประเทศไหนครับ

stupid

Пусть бредовая идея ,не рубайте с гореча ,отвечайте нам скорее через почту глав врача😂

Super

🛠️👍👍👍use oil!!!

❤Какая модель станка?

wonderful

Great way to lose a finger 😮

Cool work thanks 👍

👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

потом судья нарежет, пятёрку самое меньшее 😂

Looked like he didn't have those bearings running straight, that will cause problems plus the in/out adjustment isn't in line 🤔

funny and lying Thumbnail ^^ retard :D

Que genialidad y creatividad,buenos los video.

의대증원 이천명 증거 이천공이 시켜서 한 거임!

Good job. Regards from Australia.

I beg you. Lubrication Please! Wakodahatchee Chris

Треш...

Have been using similar steady for about 40 years. I am shure every machinist is familiar with them !